Multi-Orientation Drop Tester

Orientation Drop Tester Machine China Supplier

Multi-orientation Drop Tester is used for drop impact test on small electronic products in designated direction and specified posture. It is a practical and effective drop test equipment to determine the impact resistance of electronic products when they are accidentally dropped to the ground.

The orientation drop test machine is suitable for small electronic products like mobile phones, E-books, IPAD, etc. Especially widely used in the mobile phone manufacturing industry.

This drop test machine is allowed to be configured with different holding devices to achieve directional drop tests on the edges, corners, and surfaces of the specimen through different angles. The specimen can be lifted to a specified height and dropped to impact the pre-placed floor. During the descent, the specimen will be automatically released at a specified height such as 300 mm to guarantee that the test piece is close to its original posture at the moment of the impact. In addition to the directional drop test, this drop tester machine is also suitable for the free-fall drop test.

There are mainly two types of fixtures that are available to be fitted to this orientation drop tester. One is the pneumatic clamping device driven by cylinders. The specimen can be conveniently clamped and released by two parallel clamping plates under control. The distance between clamping plates is adjustable to accommodate specimens of different dimensions and shapes. The other is the pneumatic assembly with multiple vacuum suction cups. They can suck the specimen tightly and achieve the drop test at different angles. The vacuum suction cup is suitable for the drop test of bare mobile phones, tablets, and other electronic products. You are required to prepare the air source to ensure the fixture can work normally.

Clamping device of orientation Drop Tester

Peumatic Fixture

Vacuum sucker of Orientation Drop Tester

Vacuum Sucker

Model AT-D3001
Product Orientation drop tester
Max. Test Height 300 ~ 1800 mm (2000 mm customized)
Max. Drop Product Weight 1 / 2 kg
Min. Drop Height 300 mm
Max. Size of the Acceptable Specimen Regular 150 × 150 mm (The bigger sizes need to be customized)
Drop Posture On edges, corners, surfaces at 0°, 45°, 90° or other desired angles
Drop Angle Error about 1° ~ 3°
Counter 0 ~ 999,999 times (can be set)
Sample Holding Method Sucked or clamped by a pneumatic mechanism (can be customized)
Vacuum Adsorption Switching Mode Three vacuum chucks can be switched electronically

(independently)
Parameter Setting The drop height and adsorption height can be preset, and the number of drops is displayed and supports being cleared
Safety Door Protection Function Fully enclosed transparent acrylic plates to protect operators
Control Mode PLC programming touch screen control (drop velocity is displayable)
Drop Floor A3 steel plate (The acrylic board, wooden board, marble board and other materials can be used)
Drop Method Pneumatic drop / Free fall
Lifting Method Automated lifting
Air Source ≥ 0.5 Mpa
Power supply Power supply 1∮, 220 V AC ± 10 %, 50 / 60 Hz or specified

  • The machine adopts a fully enclosed structure with transparent acrylic protective plates to prevent hazards while testing.

  • Fitted with a touch screen for data settings and presentation.

  • Supports PLC computer programming for test control.

  • The gripping device can be tailored to testing requirements.

  • Three vacuum chucks can be switched electronically.

  • The drop impact angle of the specimen is close to the preset angle.

  • A servo motor is used to drive the corresponding module to adjust the drop height for fast and precise positioning.

  • The clamping device can be automatically raised to a set height after each test, convenient for operation and improves test efficiency.

  • The number of drops can be displayed and zeroed freely.

  • It supports two clamping methods: vacuum adsorption and pneumatic clamping.

  • Adopts a multi-angle adjustment device to achieve the drop test on edges, corners, and surfaces of the specimen at 0°, 45°, 90° or other desired angles.

  • Equipped with a safety door to provide full protection and the test stops once opened.

  • A variety of drop floors can be selected, including the steel plate, acrylic plate, wooden board, or marble board.

  • Comes with four lockable casters and a level fine-tuning device.

  • JIS C 0044
  • IEC 60068-2-32
  • YD/T 1539-2006, etc.

There are usually have three other drop testing machines used for drop tests of electronic products, including Free Fall Drop Tester, Rotating Drum Drop Tester, Package Drop Tester.

Free fall drop tester

Free Fall Drop Tester

  • AT-D3007
  • Electric lifting of the specimen
  • Specimen clamped pneumatically
  • Drop against the surface, corner or edge
  • Load of 3 kg or 5 kg
Rotating drum drop tester

Rotating Drum Drop Tester

  • AT-D3006
  • Continuous tumbling and falling
  • Single / two/ multiple drums are available
  • Load up to 5 kg
  • Applicable to small electronics
package ISTA drop tester

Pneumatic Drop Tester

  • AT-D3002
  • Drop against the surface , corner or edge
  • Electric lift
  • Pneumatic Release
  • Load up to 100 kg

The directional drop test machine can perform precisely directional drop tests. The usual drop angles are 0 degrees, 45 degrees, and 90 degrees. The operator can guide the specimen’s corners, edges, or surfaces to hit the base plate in the desired posture.

Ordinary free fall testing machines can only achieve free fall test on corners, edges, or surfaces of the specimen. The specimen may rotate during falling. The free fall test machine can’t ensure that the specimen falls in the desired posture.

Because the mobile phone manufacturers have used the directional drop tester to carry out hundreds of drop tests in the laboratory in the development phase. The mobile phone shell is made of drop-resistant materials, and the internal parts are also drop-resistant. In the laboratory, The operator needs to drop the mobile phone from a height of at least 1 meter. The six surfaces, eight corners of the mobile phone must be tested twice each. As long as there is any damage, the entire product will be judged as a failure. If the mobile phone passes a height of 1-meter drop test, then the drop height will be increased to 1.5 meters until 1.8 meters.

Send an Inquiry

Please feel free to contact us for more details on the product, price, lead time, payment terms, shipment methods, etc. Amadetech sales specialists will respond within one working day.

Contact Form Demo (#3)

Related Products